At 8am the diary says you are full. By eleven, one bay is idle waiting for parts and another holds an "hour job" that is three hours in. A busy workshop is planned around its bays, not just its hours, and here is how to do it.
Most garages plan the day in hours: eight hours open, two technicians, sixteen hours to sell. That number is almost never what you get. Cars do not queue in hours, they queue for a lift, and the moment one car sits on a ramp waiting for a part, that whole bay stops earning. The garages that stay busy without the chaos plan around the bays they have, and they plan for the day going wrong.
Work out what you can really fit in
Start by counting what can actually take a car. Not every bay is equal, so list them:
- Lifts. Most repair and servicing work needs a car in the air, so the number of lifts is usually your real limit.
- Flat bays. Fine for diagnostics, electrical work, valeting and pre-MOT checks, but not for a clutch.
- Your MOT bay. It earns as an MOT bay when a tester is in, and is a squeeze for anything else.
- Specialist kit. If only one bay has the alignment rig or the air con machine, every job needing it queues for that bay.
Then compare bays with people. Three lifts and two technicians is two lifts' worth of work, with a third lift that is useful for parking a car mid-job. Two lifts and three technicians means someone is always waiting. Your capacity is the lower of the two, minus road tests, parts runs, customer calls and lunch. Plan to fill around 80% of what is left and you have room to absorb a bad morning.
Size jobs from your own history
Book times from data providers are a fair starting point, but they assume clean fixings, the right part first time and a technician who has done the job a hundred times. Your own jobsheets tell the truth. Look back over the last couple of months and note what a full service, a set of pads and discs or a timing belt actually took you, on the cars you actually see.
It helps to book in bands rather than minutes: short jobs (under an hour), half-day jobs and full-day jobs. Add a margin for anything older or rustier than average, and for anything that starts with "it makes a noise". Diagnosis is a job in its own right, so book it as one rather than hiding it inside the repair.
Build the day in the right order
The order you put jobs into a bay matters as much as how many you fit.
- Big jobs go in first thing, each in its own bay. A full-day job started at 10am is a job finished tomorrow.
- Diagnostics go early. If the fault needs a part, you want to know before the motor factor's afternoon run, not after it.
- Short jobs fill the gaps around the big ones, and are the first to move when something overruns.
- MOTs go at fixed times. Customers like a set slot, and a tester's day is easier to plan in a steady rhythm.
- Stagger drop-offs. Ten customers at 8:30 means a queue at the counter and the first car not on a lift until nine.
Keep a bay back
Filling every bay with pre-booked work feels efficient until a regular breaks down outside, a car comes back with a warning light, or a job overruns into the afternoon. Each of those is either an unhappy customer or a reshuffle of the whole day.
Holding one bay back, at least for the morning, gives you somewhere for that work to go. If nothing turns up by lunchtime, pull a short job forward or catch up on a car that is waiting. How much to hold back depends on your trade: a garage near a busy road with lots of breakdown work needs more slack than one doing mostly booked servicing. Online booking makes this more important, because customers can fill the diary while you are under a car. Let them fill most of your bays, never all of them.
A useful rule of thumb: never let the diary fill a bay you cannot afford to lose to a breakdown. The walk-in you can fit in today is often the customer who books their next service with you.
Cars that stay longer than a day
Engine work, insurance repairs and anything waiting on a back-ordered part can tie up a bay for days. Decide early whether the car needs a lift the whole time. If it does, block the bay out for the whole stay so nothing else gets booked into it. If it does not, move it off the lift and park it, and the bay goes back to earning.
Treat your own downtime the same way. A lift going in for its thorough examination, a repair to the ramp or a day with a technician on a course all take capacity away. Put them in the diary as a bay that is out of action, not just a note on the wall, so nobody books a customer into a lift that will not be there.
When the day goes wrong
It will. What matters is how quickly you react.
- A job overruns: tell the next customer early, before they set off. Move their car into the spare bay if you kept one.
- A part is late: swap the job for one you can start now, and get the waiting car off the lift.
- A no-show: pull a short job forward, or bring in a car that is already on site.
- A job grows: quote the extra work and get approval before the bay sits idle waiting for a phone call to be returned.
Customers forgive a delay far more easily than silence. A quick message saying the car will be ready at four instead of two keeps the relationship, and the payment.
Look back once a week
Spend ten minutes at the end of each week going over it. Which bay sat empty, and when? Which jobs overran, and was it the car or the estimate? How many walk-ins and breakdowns did you turn away? Two or three weeks of honest answers will tell you more about how to book than any rule in this article, including whether you need another lift or another technician.
Whiteboard or software?
A whiteboard by the workshop door works well for two bays and one person taking bookings. It struggles when bookings arrive by phone, website and WhatsApp while you are under a car, when a job runs over three days, or when the person who knows the plan is off sick.
Garage Shift gives each bay its own column in the calendar, so you can see what every lift is doing at a glance. When you book a job it suggests the first bay that is free at that time, or free for the whole stay on a multi-day job. You can mark a bay out of action for maintenance, and choose how many bays online bookings are allowed to fill, so one stays free for walk-ins and breakdowns. You can still book that last bay yourself.
